Circuits

Work out current and voltage in a real circuit.

Take the voltage landscape from the last lesson and bend it round into a loop. A battery keeps one end of the loop higher than the other. Charge runs downhill through whatever you connect, gives up its energy there as light or heat or motion, and is lifted back to the top to go round again. That's a circuit, and nearly everything you own with a plug or a battery is one.

A battery, a switch and some bulbs on a bench, drawn so that the height of every point is its voltage. The battery is a lift and each bulb is a ramp. Drag the top of the battery to change its voltage. The white dots stand for positive charge going round from + to −, the direction current is always drawn in. Bulbs are treated as plain resistors, and the battery and the wires as having no resistance of their own. Real charges are packed far closer and move far more slowly than the dots.
  • With one bulb, drag the top of the battery up from 6 V to 12 V. The ramp is twice as tall, the charges go round twice as fast (2 A becomes 4 A), and the power goes up four times, from 12 W to 48 W.
  • Go back to 6 V and raise bulb A from 3 Ω to 6 Ω. Half the current, and a dimmer bulb. Then put it back to 3 Ω.
  • Choose "Two in series". Follow one dot: it moves at the same speed before, between and after the bulbs. What the bulbs share out is the height: 2.00 V and 4.00 V.
  • Untick "Switch closed". Everything stops at once, everywhere, and the whole 6 V appears across the gap. Then close it again.
  • Choose "Two in parallel". Each bulb now gets the full 6 V. The charges split at the junction, more of them taking the easier path, and the battery supplies 3 A where one bulb took 2 A.
  • Tick "Show the electrons instead". They go the other way round, climbing the ramps.
  • Choose "A short circuit".

Current

Current is how much charge passes a point each second:

\[ I = \frac{Q}{t} \qquad\qquad 1 \text{ amp} = 1 \text{ coulomb per second} \]

Its direction is taken to be the way positive charge would move, out of the battery's + end and round to its − end. That was settled before anyone knew what actually moves in a wire. It turned out to be electrons, which are negative and drift the other way. Nothing in this lesson depends on which you picture: negative charge going one way round carries the same current as positive charge going the other. The figure shows the conventional, positive picture unless you ask for the electrons.

The electrons are also slow. Suppose a wire of cross-section \(A\) has \(n\) free electrons in each cubic metre, each with charge \(e\), drifting along at speed \(v\). In one second, every electron within a length \(v\) of a point passes it. That's a volume \(Av\), holding \(nAv\) electrons, so

\[ I = nAve \]

Copper has \(n = 8.5 \times 10^{28}\) free electrons per cubic metre. Take a wire with a cross-section of 1 mm², which is \(A = 10^{-6}\) m². Then \(nAe\) is \(8.5 \times 10^{28} \times 10^{-6} \times 1.60 \times 10^{-19}\), which comes to \(1.36 \times 10^4\): that many coulombs of free electrons in every metre of the wire. For a current of 1 A,

\[ v = \frac{I}{nAe} = \frac{1}{1.36 \times 10^4} \approx 7.4 \times 10^{-5} \text{ m/s} \]

That's 0.07 mm a second, about a quarter of a metre an hour. The lamp still lights the moment you close the switch, because the wire is full of electrons already and they all start moving together, like water in a hose that's already full.

Round the loop

The battery gives each coulomb some energy: lifts it, in the picture. Each thing the current passes through takes some away. Voltage is a height, and after one full lap you are back where you started, so the ups and downs must cancel. This is Kirchhoff's loop rule:

Round any closed loop, the rises in voltage add up to the same as the drops.

It's the fact from the last lesson that a round trip takes no work, applied to a circuit. With the switch open there's no current, so nothing in the loop drops any voltage, and the only place left for the battery's 6 V to go is across the gap.

There's a second rule, for charge. Charge doesn't pile up where wires meet, or leak away, so:

At any junction, the current flowing in equals the current flowing out.

That's Kirchhoff's junction rule. It's why the dots move at the same speed all the way round a single loop. Current isn't used up by a bulb. What gets used is the height.

Resistance

How much current flows for a given voltage depends on what it has to flow through. In a metal, the electrons keep colliding with the atoms and handing over the energy the battery gave them, which is why the wire warms up. For metals at a steady temperature, and for many other things, the current is proportional to the voltage across them. The constant that links them is the resistance, \(R\), measured in ohms (Ω), and the rule is Ohm's law:

\[ V = IR \]

One ohm lets 1 amp through for each volt. Ohm's law is a description of how many materials behave, not a law of nature. A real bulb's filament gets hotter as it brightens and its resistance goes up, and some components don't follow it at all.

Power

A bulb turns electrical energy into light and heat. To find how fast, count the energy one charge at a time.

Each coulomb that goes through the bulb comes down \(V\) volts, so it gives up \(V\) joules.

\[ \text{energy for each coulomb} = V \]

\(I\) coulombs go through every second.

\[ \text{coulombs each second} = I \]

Multiply them for the joules each second, which is the power in watts.

\[ P = IV \]

Ohm's law lets you write it with the resistance instead. Put \(V = IR\), or put \(I = \frac{V}{R}\):

\[ P = I^2R = \frac{V^2}{R} \]
\[ P = IV = I^2R = \frac{V^2}{R} \]

In the figure's first circuit, 2 A comes down 6 V, so the bulb gets \(2 \times 6 = 12\) W. Doubling the voltage doubles the current as well, which is why the power went up four times.

Series and parallel

In series, the bulbs are one after the other on a single path. The same current \(I\) goes through both, and the loop rule says their drops add up to the battery's voltage:

\[ V = IR_1 + IR_2 = I(R_1 + R_2) \]

So together they behave like one resistance \(R_1 + R_2\). Each takes a share of the height in proportion to its own resistance.

In parallel, each bulb has its own path from the top wire to the bottom one. Both have the same voltage \(V\) across them, and the junction rule says the battery's current is the two added together:

\[ I = \frac{V}{R_1} + \frac{V}{R_2} = V\left(\frac{1}{R_1} + \frac{1}{R_2}\right) \]

Compare that with \(I = \frac{V}{R}\) for a single resistance, and the pair behave like one resistance \(R\) with \(\frac{1}{R} = \frac{1}{R_1} + \frac{1}{R_2}\).

\[ \text{series: } R = R_1 + R_2 \qquad\qquad \text{parallel: } \frac{1}{R} = \frac{1}{R_1} + \frac{1}{R_2} \]

The figure's 3 Ω and 6 Ω make 9 Ω in series. In parallel, \(\frac{1}{R} = \frac{1}{3} + \frac{1}{6} = \frac{1}{2}\), so \(R = 2\) Ω, less than either. Adding a path can only make it easier for current to flow.

The sockets in a house are in parallel, so that everything gets the full mains voltage and one thing can be switched off without the rest going dark. The price is that the currents add up in the wire they share.

Short circuits

Ohm's law has no upper limit. If the two ends of a battery are joined by something with almost no resistance, \(I = \frac{V}{R}\) is enormous, and so is the heat, \(\frac{V^2}{R}\). In the figure, 6 V across 0.05 Ω of bare wire drives 120 A and makes 720 W, in a wire that might safely carry a few amps. It glows and melts, and anything near it can catch fire.

That's what fuses and circuit breakers are for. Each is a weak point made on purpose, which breaks the loop when the current goes above a safe value.

A real battery can't quite manage what the figure shows, because it has some resistance of its own inside. A car battery's is about a hundredth of an ohm, so it really can push hundreds of amps through a dropped spanner. A torch cell's is a few tenths of an ohm, which holds it to a few amps. Then most of the heat is made inside the cell, which is no better.

A capacitor: a first look

A capacitor is two metal plates close together with an insulator between them. Connect it to a battery, and charge is taken off one plate and put on the other until the voltage between them matches the battery's. The charge it holds on each plate is proportional to that voltage:

\[ Q = CV \]

\(C\) is its capacitance, in farads. One farad is a coulomb for each volt, and it's a big unit: the ones in the figure are a few hundred millionths of a farad (microfarads, µF).

Put a resistor in the way and the filling takes time.

A 9 V battery charging a capacitor through a resistor, drawn the same way: height is voltage. The capacitor's top plate rises as charge collects on it, so the ramp across the resistor gets shallower. The graph is the capacitor's voltage over one run, which starts afresh whenever you throw the switch or move a slider.
  • Press "Empty it and start again" and watch the ramp. It starts steep, with the charges racing, and flattens as the capacitor fills.
  • The white dot on the graph marks one time constant, 2 s here. By then the capacitor has covered 63% of the distance to 9 V.
  • Raise the resistor to 40 kΩ and start again. The curve is the same shape, stretched to twice the time.
  • Put it back to 20 kΩ and raise the capacitor to 200 µF. Its plates are wider and need twice the charge for each volt, so again it takes twice as long.
  • While it's part full, switch it to "A plain wire". Now its own voltage drives the charge back out, quickly at first and then more and more slowly.

Call the battery's voltage \(V_b\) and the capacitor's \(V_C\).

The loop rule: the battery's rise equals the drop across the resistor plus the capacitor's voltage. So the current is set by the gap between the two.

\[ V_b = IR + V_C \quad\Rightarrow\quad I = \frac{V_b - V_C}{R} \]

That current is charge arriving on the plate each second, and \(Q = CV_C\).

\[ I = \frac{dQ}{dt} = C\,\frac{dV_C}{dt} \]

Put the two together. The capacitor's voltage rises at a rate proportional to the gap that's left.

\[ \frac{dV_C}{dt} = \frac{V_b - V_C}{RC} \]

Call the gap \(u = V_b - V_C\). Every volt the capacitor gains, the gap loses, so the gap shrinks at a rate proportional to itself.

\[ \frac{du}{dt} = -\frac{u}{RC} \]

The function that falls at a rate proportional to its own size is the decaying exponential. The gap starts at \(V_b\), with the capacitor empty. You can check this by differentiating it with the chain rule.

\[ u = V_b\,e^{-t/RC} \]

The capacitor's voltage is the battery's minus the gap.

\[ V_C = V_b\left(1 - e^{-t/RC}\right) \]
\[ V_C = V_b\left(1 - e^{-t/RC}\right) \qquad\qquad \text{time constant} = RC \]

Ohms times farads comes out in seconds. After one time constant the gap has shrunk to \(e^{-1} = 37\%\) of what it was, so the capacitor is 63% of the way there. After two it's 86%, after three 95%, and after five more than 99%. It never quite arrives. Emptying is the same decay with nothing to aim for but zero: \(V_C = V_0\,e^{-t/RC}\), where \(V_0\) is what it started with. Its half-life, from the formula in the exponentials lesson with \(k = \frac{1}{RC}\), is \(RC\ln 2\).

Kirchhoff's two rules are the conservation of energy and of charge, written for wires. They're enough to work out any network of batteries and resistors, however tangled. And the capacitor's curve turns up wherever something fills or drains through a resistance. A nerve cell's wall is a capacitor that leaks through a resistance, and its time constant, some thousandths of a second, limits how quickly its voltage can change. The same thing is one of the limits on a computer chip: every wire in it has to be charged up through a resistance before the next step can begin.

Problems

A current of 2.0 A flows through a torch bulb for one minute. How much charge has passed through it? How many electrons is that? Each carries \(1.60 \times 10^{-19}\) C.

Answer

\(Q = It = 2.0 \times 60 = 120\) C. That's \(\frac{120}{1.60 \times 10^{-19}} = 7.5 \times 10^{20}\) electrons.

A car headlamp bulb is marked 12 V, 55 W. What current does it draw, and what is its resistance when it's lit?

Answer

From \(P = IV\), \(I = \frac{55}{12} \approx 4.58\) A. Then \(R = \frac{V}{I} = \frac{12}{4.58} \approx 2.62\) Ω. Or go straight there with \(P = \frac{V^2}{R}\): \(R = \frac{12^2}{55} = \frac{144}{55} \approx 2.62\) Ω.

A 3 Ω bulb and a 6 Ω bulb are connected in series to a 6 V battery. Find the current, the voltage across each bulb and the power each one gets. Then connect them in parallel to the same battery and do it again. Which bulb is brighter each time? Check both on the figure.

Answer

In series the resistance is \(3 + 6 = 9\) Ω, so \(I = \frac{6}{9} \approx 0.667\) A through both. The drops are \(0.667 \times 3 = 2.00\) V and \(0.667 \times 6 = 4.00\) V, which add up to 6 V. The powers are \(I^2R\): \(0.667^2 \times 3 \approx 1.33\) W and \(0.667^2 \times 6 \approx 2.67\) W. The 6 Ω bulb is brighter.

In parallel each has the full 6 V. The currents are \(\frac{6}{3} = 2\) A and \(\frac{6}{6} = 1\) A, 3 A in all, and the powers are \(2 \times 6 = 12\) W and \(1 \times 6 = 6\) W. Now the 3 Ω bulb is brighter, and both are far brighter than before. With the same current, the bigger resistance gets more power (\(I^2R\)). With the same voltage, the smaller one does (\(\frac{V^2}{R}\)).

A 2,300 W kettle and a 1,840 W heater are plugged into the same 230 V circuit, which has a breaker that trips at 16 A. What current does each draw? What happens when both are on?

Answer

\(I = \frac{P}{V}\): the kettle draws \(\frac{2300}{230} = 10\) A and the heater \(\frac{1840}{230} = 8\) A. They're in parallel, so the currents add in the wire they share: 18 A. That's more than 16 A, so the breaker trips. Either one alone is fine.

A 12 V car battery has a resistance of 0.010 Ω inside it. A spanner with a resistance of 0.002 Ω is dropped across its terminals. What current flows? How much heat is made each second in the spanner, and how much inside the battery?

Answer

The battery's own resistance is in series with the spanner, so the loop has \(0.010 + 0.002 = 0.012\) Ω. \(I = \frac{12}{0.012} = 1{,}000\) A. In the spanner, \(P = I^2R = 1000^2 \times 0.002 = 2{,}000\) W. Inside the battery, \(1000^2 \times 0.010 = 10{,}000\) W. Together that's the \(12 \times 1000 = 12{,}000\) W the battery is supplying. A spanner across a car battery gets red hot in seconds.

A 100 µF capacitor is charged from a 9 V battery through a 20 kΩ resistor, as the second figure first appears. What is the time constant? What is the capacitor's voltage after 2 s, and after 4 s? How long does it take to reach 4.5 V? Check them on the figure.

Answer

\(RC = 20{,}000 \times 100 \times 10^{-6} = 2.0\) s. After 2 s, which is one time constant, \(V_C = 9(1 - e^{-1}) = 9 \times 0.6321 \approx 5.69\) V. After 4 s, \(V_C = 9(1 - e^{-2}) = 9 \times 0.8647 \approx 7.78\) V. For 4.5 V, half way, the gap has to halve: \(e^{-t/RC} = \frac{1}{2}\), so \(t = RC\ln 2 = 2.0 \times 0.693 \approx 1.39\) s.

Learn more

An unhandled error has occurred. Reload 🗙